Are you getting sand with water from your faucet? If yes, then this writing will be valuable for you. We will discuss this problem here and especially about how to get rid of sand from well water.
Sand in well water often indicates a serious problem, and it can create some additional questions too. For example- sand in well water can lead to clogging of fixtures and premature replacement of fixtures and appliances. Even though appliances like a washing machine can be worn out before time.
We understand this is a big issue for you. It is the reason we felt the urge to write about it. Here, we will write about how to get rid of sand from well water. But before that, we want to discuss some reasons behind that so that you can identify why you are getting sand in water.
Some Reasons for Getting Sand in Well Water
Well Pump Wasn’t Set Properly
If all of a sudden, your well starts to pump sand, then maybe your pump of the well wasn’t set correctly. Perhaps it was set too low in well and your pump is filling with sand.
Most of the wells use submersible pumps that are set in the down of water in a case. Usually, pumps are set ten to twenty feet above the water well. But maybe yours one is set in too low, pumping sand from well’s bottom.
Too Large Well Pump
In some situations, the pump of the well may be more potent than the well, and it starts pulling sand from the aquifer.
From these sand pumps, the valve can be severely affected, and also it can build-up sand at the bottom of the well.
Well Screen or Case Degraded
After drilling the well, it is lined with steel, iron which is usually known as a case. By the driller, this case is installed in the shaft of well.
The grooves of well casing assist water is entering into the well from the nearby groundwater. Also, it restrains sand and grit from mixing with water. This is the screen of well.
The screen of a well can be damaged or eroded over time, which allows sand and silt to mix with water and pumped into your water.
If you notice the sudden existence of sand in your water, it is not a good indication and we shouldn’t ignore it. You should take further steps for inspecting the source and how to get rid of sand in well water.
How can you Get Rid of Sand in Well Water?
So we are going to provide some step by step for you about how to get rid of sand in well water.
Don't take any risk when the issue is Drinking Water. You can check Few Suggested Filter Reviews in 2023:
Step 1- Identify the type of Sand in your Water
So, in the first step, it is essential to determine where the sand is coming. Is it coming from your well or your rotten pipe?
Does your home have galvanized iron pipes? Then maybe the corrosion causes the coating in the pipe to abate and has added what is appearing sand in the water.
Another reason for getting sand in well water is the deterioration of the water heater tank. Almost all the water heater tank builds with glass lining, which deteriorated with time and appeared in water like sand.
In the water, heater anode rode also exists, and it can erode over time which may appear as brown sand in the tap and appliances. Try to fill up one white bucket with water directly from the well if you can identify any sand.
Step 2- Test Your Water
In the second step, test your water for iron, manganese, tannin, sulfur or any other particles. If possible, ask the lab to perform a count of particles in water. If your water contains a high level of iron, sulfur, tannin or other particles, then another action than just a sediment filter system is needed.
Keep in mind water filters are appropriate for sand removal but not for iron, manganese because they dissolved in the water.
Step 3- Choosing the Appropriate Well Water Filters
You can choose from the following 4 water filters or can combine the 4 for optimal performance.
Centrifugal Sand Separators
It can remove 98% of sand from water. Generally, it follows the centrifugal force for separating sand from water. It doesn’t have any moving parts which will be worn out over time, and it increases its life span.
It doesn’t require any cartridges to replace, no cones to clean and also easy to maintain. The only thing you have to do is purged the separator sometimes.
Rusco Spindown Filter Screens
For filtering out and trapping the sand and sediment of water, it uses a screen. It has a manual flush valve and occasionally, this manual valve needs to be opened for flushing out.
Spin down filter’s cartridge lasts long and only needs to be flushed, not a replacement.
Micron-Rated Sediment Filter Cartridge Systems
The filter cartridge system can restrain small particles even they are micron-sized. This can be super helpful as they can separate such small particles from water.
Auto-Backwash Sediment Filtration Systems
It doesn’t have any filter cartridges and requires the lowest maintenance. Instead of the cartridge, it uses an automatically back-washed loose filter media. This works best for sediment removal but not for sand removal.
A centrifugal sand separator with an automated backwash filter will work for both sand and sediment.
Conclusion
In the upper part, we have tried to mention the reasons for getting sand in well water as well as steps on how you can get rid of sand in well water. We hope that from the writing, you will get appropriate information.
We can’t imagine our life without water, and clear water is essential for our lives. If you are getting sand in your well water, it is indicating a significant problem in your well, fixture systems.
Apart from this, using and consuming sand well water is not suitable for our health and it can also create a problem in our all work like- washing dishes, clothes, etc.